Parts & Accessories

The Wahoo RPM cadence sensor is your sleek little solution for measuring cycling cadence data. It is wireless, magnet-less, lightweight, and easily mounts to your bike's crank arm or to your shoe. Bluetooth Smart and ANT+ dual band technology allows you to connect to and display data on both smartphones and GPS bike computers. Collecting cadence data has never been this easy. - Both ANT+ and Bluetooth Smart capabilities allow for a wireless connection to both smartphones and bike computers. - No tangled wires on your bike to connect the sensor to your device. - It only weighs 7 grams! - Provides accurate cadence data during your ride - (1) mount with double sided 3M tape, or (2) use the silicone sleeve and mount with zip ties. - The RPM can be worn on your shoe for spin classes or use with multiple bikes - Two LED lights show the sensor's device connection (blue) and cadence detection (red) - No charging required! Operates on a coin cell battery for up to 1 years. - RPM cadence sensor will fit with most bikes and frame sizes

All you need for cycling data, all together at once! The Wahoo RPM Speed and Cadence sensors are both a sleek, wireless, and magnet-less solution. Each mounts easily to your bike and the Bluetooth Smart and ANT+ duel band technology allows you to connect and display data on both smartphone and bike computers. - Dimensions (LxWxH): 1.25" x.75" x 1" - Weight: 7 grams (without mount) - Battery: CR2032 - Battery Life: Up to 12 months - Water Rating: IPX7 (waterproof up to 5 ft) - Wireless Signal Strength: Up to 10 feet - Note: Speed Sensor is NOT compatible with spin bikes

The Wahoo TRACKR SPEED sensor is the sleek, magnet-less solution for capturing cycling speed data. It easily mounts to your bike's front wheel hub, and the Bluetooth Smart and ANT+ dual band technology allows you to connect to and display data on both smartphones and bike computers. Tracking speed data has never been this easy.

TRACKR RADAR’s quick-connect strap and quarter-turn mount make installation easy across a wide range of bike frames. Three mount wedges—round/aero, D-shape, and flat—ensure a secure, stable fit no matter your setup.

SRAM eTap batteries are literally a snap to remove and charge. Just flip the tool-free battery latch up and slide the battery up and out of the derailleur. Then snap the battery into the USB powered charger and connect the charger to any USB power source or A/C USB adaptor. A full charge takes just 45 minutes to complete. - Finish: Black - Compatibility: SRAM RED eTap

SRAM eTap Battery is the power source for the eTap system. The same power unit is interchangeable between front and rear derailleurs. - Up to 1000 kilometers of riding per charge - Weight: 24g - Finish: Black - Compatibility: SRAM RED eTap

Keep your handlebar organized and your devices secure with the SGS-400-OS (27.2/31.8/35.0mm) from Minoura. - Holds up to 2 accessories (light, computer, mp3, bottle cage holder, etc.) - Lightweight and rustproof alloy construction - New LW-Clamp reduces weight 25 grams compared to previous models - Aluminum bar is position adjustable and uses Hex Bolt to install and remove - 27mm-35mm diameter

Keep your handlebar organized and your devices secure with the SGS-400-STD (22.2/25.4/28.6mm) from Minoura. - Holds up to 2 accessories (light, computer, mp3, bottle cage holder, etc.) - Lightweight and rustproof alloy construction - New LW-Clamp reduces weight 25 grams compared to previous models - Aluminum bar is position adjustable and uses Hex Bolt to install and remove - 22mm-29mm diameter

Convert your K-Edge Garmin Computer Mount to be a Computer + Action Camera combination mount. Works with any camera that utilizes the GoPro sytle interface, including GoPro Hero, Garmin VIRB, and Shimano CM-1000. - Camera Adapter mount with GoPro style interface - Fits K-EDGE Garmin Mounts (K13-500, K13-505, K13-560) - Locks GoPro, Shimano, VIRB style cameras underneath Garmin Computer. - Centers camera in out of site position - Improves video clarity by removing plastic mount shake - Colors: Anodized Black - Weight: 14grams *Note: Garmin VIRB requires the GoPro adapter that is included in the box with the VIRB.

A lightweight and highly adjustable mount for positioning any Garmin computer on aero bars. The pivoting two piece design offers multiple mounting positions based on aero bars, hydration systems and rider preference. - For 22.2mm diameter aero bar extensions - Compatible with all Garmin EDGE computers - Highly adjustable for multitude of mounting positions - Replaceable Garmin Insert with K-EDGE “Definitive Click” locking system - GoPro Interface Compatible - Weight: 29g - Anodized Colors: Black, Red, Blue - Made in Boise, Idaho, USA - Lifetime Guarantee against material or manufacture defects. Damages due to abuse or crashing excluded

The K-EDGE Gravity Top Cap is a great computer mount for those mountain riders that already a lot going on with the cockpit of their bikes, or just want a simple and sleek looking computer mount. The Top Cap replaces your already existing top cap with the K-EDGE Gravity top cap. Ideal position for Downhill and Enduro racing/riding, but is also a popular solution for any bike when using a smaller style computer (20, 25, 200, 500, 510, 520, 820). - CNC Machined 6061-T6 Aluminum Platform, Injection Molded Garmin Specific Co- Polymer Interface - Compatibility: All Garmin Edge® Computers including the 1030*, 1000*, 820, 810*, 800*, 510, 520, 500, 200, 25, 20. Also supports the Touring, Touring Plus, Forerunner 310XT, and 910XT. (Larger EDGE computers such as 800, 810, 1000, 1030 may interfere with very steep, upright, stem angles.) - Made in Boise, Idaho, USA. - Lifetime Guarantee against material or manufacture defects. Damages due to abuse or crashing excluded.

The K-EDGE co-polymer insert for Garmin 1/4 Turn style computers is a replaceable item. While it is extremely strong, we designed this insert to fail on a significant impact before the tabs on the back of the Garmin break. - Qty 1 – K-EDGE Co-polymer Insert for Garmin 1/4 Computer (Part No. K13-503) - Qty 2 – M3 x 0.5mm x 6mm with Pre-Applied Nylon 180,18-8 S.S. Screws

- For use with trainers and spin bikes only - Holds iPad Mini, Kindle Fire, Nexus 7, Samsung Galaxy 7 - Includes touch screen friendly splash-proof bag - Universal clamp attaches to all round bars up to 1.5" diameter - Viewing perspective can be set for preference - landscape or portrait - Instant removal and installation of device - Neat rubber bumpers grip and help cushion device - Mini-Tablet Holder max dimensions: - Holds devices with max dims 8.6" x 5.5" x .625" | 220 x 140 x 15mm (H x W x D)

Accessory Mount from Cane Creek.

Get more data from your rides with the Bontrager Interchange digital combo speed and cadence sensor. This ANT+ 2.4 Ghz is designed to work with Bontrager Node wireless computers. It also works with many other ANT+ enabled devices. Sensor adjustment is easy with the adjustable arm. • ANT+ 2.4 Ghz and Bluetooth Smart wireless digital speed and cadence sensor • ANT+ and Bluetooth Smart allow simultaneous use of Trip 300 and smartphone • For use with many ANT+ and Bluetooth Smart wireless technology enabled devices • Independently adjustable arm for precise alignment of speed and cadence sensors • Includes Bontrager wheel magnet and crank cadence band • Includes silicone mounting strap to fit most chainstays and CR2032 battery • Visit www.thisisant.com/directory/ for compatible ANT+ devices • Visit www.bluetooth.com/pages/bluetooth-smart-devices.aspx for compatible Bluetooth devices

Handlebar computer mount for Garmin/Wahoo for Vuka Shift AXS

Aerodynamic dual-bottle BTA hydration system that features a dynamic, multi-position computer mount to accommodate your changing needs. Raise the computer mount up to tuck in a refill bottle for race day, or lower it down for a standard bottle while maintaining the optimal view for training days. - Telescoping Garmin mount features on-the-go tilt adjust to avoid glare. - Zero-leak design with a sealed viewing window to easily monitor liquid levels, and a leak-free Dolphin Breather Valve that lets air in but doesn't let water out. - Capacity: 26oz (768 mL) - Material: Plate: 6061-T6 Aluminum - Cage: Nylon Composite Vee Cage - Computer Mount: Nylon Composite - Bottle: Lead free, BPA-Free and HDPE food safe certified bottle - Brackets: Nylon composite with Velcro straps coated with no-slip extension grip - Adjustment Width: 75-150mm - Weight: 9.3oz (265g)

Telescoping Garmin Computer Mount for Versa Plates. Raise the computer up for Refill Bottles, or lower it down to clear Standard Bottles. On-the-go tilt adjust to avoid glare. - Telescoping computer mount makes for a seamless switch between Refill or Standard Bottle - Compatible with Garmin bike computers and Multisport Watches - Requires Versa Carbon Mount or Versa Aluminum Mount Telescoping Garmin-Specific Computer Mount - Raise the computer mount up to tuck in a Refill Bottle for race day, or seamlessly lower it down for a Standard Bottle to maintain the optimal view for training days. Compatible with Garmin bike computers and multisport watches. On-the-Go Computer Tilt Adjust - Avoid changing glare with a tilt mechanism for easy adjustments while you ride Arrives Fully Assembled - Few steps required to install and head out on your first ride - Weight: 1.9oz (54g) - Construction: Nylon Composite Includes - Fully assembled computer mount - 2 screw sets: one for Versa Carbon Plates, and one for Versa Aluminum Plates Warranty: Limited Lifetime

Gain more room or find the perfect position for lights, computers, music players, GPS, or whatever, with the Topeak BarXtender. Attaches securely to the handlebars or stem and adjusts for optimum position. - Clamp: Fits 22-38 mm tubes (shims included) - Crossbar: Device mount bar 25.4 mm - Material: Engineering Grade Plastic and Steel - Mount: Handlebar, Handlebar Stem - Size (L x W x H): 18 x 3 x 3 cm, 7.1” x 1.2” x 1.2” (folded) - Size (L x W x H): 13 x 10 x 3 cm, 5.1” x 3.9” x 1.2” (open) - Weight: 116 g / 4.08 oz

This handlebar bracket has been developed so you can attach a tablet to your handlebars. The design provides a safe distance so that no sweat falls on the screen while you are training. - Suitable for handlebars with a diameter ranging from 26mm to 35mm - Adjustable to different tablet sizes: length 182-267mm, width 112-197mm, max. thickness 13mm

Securely holds your Turbo Connect Display/Speedzone 2 computer. - Specialized Turbo Connect Display mount. - Left- and right-side compatible. - Mountain bike design situates a CPU above stem. - Fits 35mm handlebars.

Securely holds your Turbo Connect Display/Speedzone 2 computer. - Specialized Turbo Connect Display (TCD)/Speedzone 2 Display mount. - Left- and right-side compatible. - MTB-style above-the-stem mount.

Securely holds your Turbo Connect Display/Speedzone 2 computer. - Specialized Turbo Connect Display (TCD)/Speedzone 2 Display mount. - Left- and right-side compatible. - Road-style above-the-stem mount.

Connects the Specialized SL Range Extender Battery with 2nd generation Turbo Levo SL Comp, Comp Carbon, Expert Carbon, and S-Works models. Custom connector with lock mechanism ensures a secure connection. Length: 145mm

SL Range Extender Cable 285mm MTB

Charge your Specialized Turbo battery with this high output, custom Li-ion charger. • Custom Specialized Li-ion battery charger • Output: 42V4A • Compact design while delivering huge power • With Rosenberger plug and light indication of the charging status

Whether it's just having a second battery for peace of mind, or for carrying on a ride you know is going to require a bit more juice, Specialized's Turbo SC battery has a long lifecycle for that extra distance. It charges super fast and has a massive 691Wh capacity. - Custom Li-Ion battery for Turbo. - 691Wh capacity (60 cells x 3.2Ah) with ANT/BT module to connect to external devices. - Allows super-fast charging times and a long life cycle.

Shimano Di2 External Battery Mounts - All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions - Use Di2 system checker to update component firmware

- Di2 internal battery, fits all e-Tube Di2 groups - Capacity: 500 mAH (± 2000km) - Use with EW-WU101 or SC-MT800 interfaces/junction to gain BlueTooth Smart wireless connectivity for on-the-fly adjustments with smartphones and tablets - Requires SM-BCR2 charger

The new DN300 Built-In type battery features the same waterproof design that Di2 users have loved for generations. Now with 3 ports, it delivers stable power to Shimano's 12-speed road derailleurs (and shifters if a fully wired option is selected). - Compatible with thinner next-generation electric wire SD300 and systems after R9250/R8150 series - Li-Ion type - Capacity: 500 mAH |3.7Wh (± 2000km autonomy) - Rated voltage: 7.4V - Charges through RD-R9250 |RD-R8150 rear derailleur using EW-EC300 Di2 Charging Cable (sold separately) - Fixing small parts included - Weight: 52g

Shimano BT-R1A External Di2 Battery - All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions - Use Di2 system checker to update component firmware - Di2 External Battery, battery charger, and power cable are universal between Dura-Ace 9070, 7970, Ultegra 6870, 6770 and Alfine Di2 systems - Battery weight: 71 grams

The Shimano EW-EC300 Charging Cable is compatible with new Shimano 12-speed road Di2 systems. This cable will also recharge the Dura-Ace R9200 and Ultegra R8100 power meter cranksets. 1700mm cable length

Shimano Di2 Frame Junction Box - Frame Junction Box connects via SD50 E-tube wires to four different points: front derailleur, rear derailleur, cockpit junction box and battery mount - All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions - Use Di2 system checker to update component firmware from http://e-tubeproject.shimano.com/

Shimano Di2 Junction Box - All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions - Use Di2 system checker to update component firmware from http://e-tubeproject.shimano.com/ - SM-EW90-A 3-Port Cockpit Junction Box connects 1 pair of Di2 shifters to the frame junction box via 3 SD50 E-tube wires - OEM front wiring kit for Dura-Ace Di2 9070 - LED battery charge level indicator - Rear Derailleur adjustment mode - Internal Battery charging port - Includes Junction Box Band (CY9082) and Junction Box Hook (Mounting Plate, CY9081)

Shimano Di2 Frame Junction Box Frame Junction Box connects via SD50 E-tube wires to four different points: front derailleur, rear derailleur, cockpit junction box and battery mount All Di2 components on the bicycle require the same firmware version. Using Di2 components with different firmware versions may cause malfunctions Use Di2 system checker to update component firmware from http://e-tubeproject.shimano.com/

Shimano SM-PCE02 link cable for e-tube and Di2 systems.

The QuickView was designed to put the Garmin Edge Computer out in front of the stem. Fits Garmin 605 and 705. - Glass-filled nylon, stainless steel Torx T25 bolt - Weight: 20g

- Shift buttons mounted to the end of a bar plug - Included wire connects to Blip Box - Fits bars with 19 - 20.5mm inside diameter

Be it the fireworks of a finale, an ideal rhythm, climbing on the top, or a deep, dark place extracting the last kilojoule of effort on your bike split, you want to adjust your gear with the twitch of a finger. eTap Blip satellite shifters allow you to shift when you want, where you want. - Limitless remote shifting positions for drop and aero bars - Wired shift buttons can be positioned however the rider prefers - Connect to Blip Box or drop bar eTap levers - Compatible with SRAM RED eTap shift/brake controls

- Use to keep Blips in place on handlebars - Fits 31.8mm round portion of drop bar - Clamp mounts directly to bar outside of tape zone - Ideal for use with thumbs or index fingers while hands are on the tops - Right and left specific, just like Blips - Weight: 12 grams (for pair) - Material: Polypropylene - Compatibility: 11-speed - Recommended Group: SRAM RED eTap

External Blip mount for aero extensions and base bars - 360 degree rotation for adjustment - Aero use only to fit 22.2mm OD bar 65mm in length - Fits all Zipp aero extensions and base bars - Blips not included - Weight: 57 grams for pair (does not include Blip) - Material: Polypropylene + TPE - Compatibility: 11-speed - Recommended Group: SRAM RED eTap

To use with your Bryton, Garmin, or Wahoo computer, the Ritchey Lollipop Accessory Mount allows you to integrate your favorite device with your Ritchey cockpit. Compatible with the Universal Stem Mount and Computer Mount Adapter for the SuperLogic Butano Ridge handlebar, the Lollipop Accessory Mount will also accept a GoPro camera to give you total control over your performance metrics as well as your ride aesthetics.

Free up bar space and secure your GoPro and many other stem-mounted accessories with our Ritchey Universal Stem Mount. Our unique mount means clutter- and hassle-free mounting of your favorite devices where they're easily viewed and operated. - Compatible with Ritchey C220 and 4-Axis 44 stem faceplates - Forged and machined alloy - Includes extended-length hardware

Mount your bike computer directly to your ShockStop Suspension Stem. The ShockStop Computer Mount puts your Garmin, Wahoo, Cateye, Joule, Mio, Magellan, or Polar bike computer in perfect position. Two different mounting positions let you fine-tune the fit of your computer and tuck it out of the wind. Benefits: - Conveniently places your computer directly in front of your stem within easy reach - Two different mounting options let you fine-tune the position of your computer Details: - Fits ShockStop Suspension Stem only (Note: using the computer mount with the +30 degree stem will place the computer in a very upright position in line with the stem) - 2 different mounting positions (upper & lower) Compatibility: - Compatible with Garmin Forerunner QR kits - Compatible with Garmin Edge 1000 in portrait and landscape mode (upper position) and landscape mode only for lower position - Compatible with Wahoo Element and Polar in the upper position only

This mount integrates with your Quick-Release Aerobars by attaching directly to one of the aerobar handlebar clamps and provides and out-front section of bar for attaching computers or other accessories. Benefits: - Positions your computer for easy viewing in road or aero riding positions - Stays attached to your bicycle when aerobars are removed Details: - Provides two mounting heights and 3 positions to fine tune your computer's position - Integrates with the optional Water Bottle Mount, putting all your essentials at your fingertips - Includes all necessary mounting hardware

Profile Design's UCM Universal Computer Mount provides a convenient 25mm long place to mount your computer on your aero bars. It installs without tools, stays put and can be positioned as needed for easily viewing and controlling your computer.

Profile Design's UCM XL Universal Computer Mount provides a convenient 60mm-long place to mount your computer on your aero bars. It installs without tools, stays put and can be positioned as needed for easily viewing and controlling your computer.

The Under Stem Mount allows riders to secure a Shimano Di2 Junction Box to their bike quickly and easily without the need for zip ties, duct tape, or other unreliable attachments. - Lightweight alloy headset spacer with nylon body (9g) - Compatible only with Shimano Di2 Junction Box - 95mm length, 44mm width, 6mm height - 6 Degree angle

- Discreet way to install an Apple AirTag inside your tubeless tire - Identify the location of a stolen bike, enabling the owner to alert local authorities for retrieval - AirTag is housed in a 3-part silicone and rubber tubeless valve mount - Sacrificial stem, ensures tracker and rim protection under impact - Silicone top cover protects tracker and internal plug reduces sealant ingress - Supplied with 3 pairs of our rubber valve bases to suit different rim profiles for the optimum seal - Note the Tubeless Secure Tag Holder can only be used in rear wheels – not for use on the front wheel Compatible tire types: - MTB tyres (XC, Enduro Trail, Downhill) - Gravel Tires (the narrowest recommended tyre size is 38mm wide)

- Discreet way to install an Apple AirTag inside your tubeless tire - Identify the location of a stolen bike, enabling the owner to alert local authorities for retrieval - AirTag is housed in a 3-part silicone and rubber tubeless valve mount - Sacrificial stem, ensures tracker and rim protection under impact - Silicone top cover protects tracker and internal plug reduces sealant ingress - Supplied with 3 pairs of our rubber valve bases to suit different rim profiles for the optimum seal Note the Tubeless Secure Tag Holder can only be used in rear wheels – not for use on the front wheel Compatible tire types: - MTB tyres (XC, Enduro Trail, Downhill) - Gravel Tires (the narrowest recommended tyre size is 38mm wide)

- Pakyak auxiliary battery holder to mount Pakyak auxiliary battery inside the storage box.

Replacement magnet for MSW Miniac Double Speed & Cadence computers. Includes water-resistant cadence magnet and four plastic zip ties for mounting to pedal crank arm.

- Machined protective case that houses the Apple AirTag on the bottle cage mount. Apple Air Tag sold separately - Casing is not waterproof but the Apple AirTag is rated IP67 (water resistant) - Removal key for T25 bolts security bolts included - Fits discreetly under a water bottle cage or mounted to accessory top tube bolts

Easily secure your GPS cycling computer to your favorite bike. Includes: - Two sets of O-rings (two diameters) - A backup O-ring in each size

- Machined protective case that houses the Apple AirTag under your saddle. Apple AirTag sold separately - Casing is not waterproof but the Apple AirTag is rated IP67 (water resistant) - Compatible with some saddle bags - Mounts to saddle rails

KMC's digital ChainChecker is the most accurate tool for checking your chain’s elongation. - Measures up to 2.5mm elongation - Fits all chains including 11 speed - Handy electronic device - Stainless hardened metal body

The K-EDGE Garmin Stem Mount is a great upgrade solution for cyclists who prefer their computer above the stem. Mounting off of the steerer tube, the mount replaces a standard 5mm spacer, and is locked securely in place by the top cap compression system. The adjustable version allows for a variety of different stem angles. Can be used with positive or negative degree stems and additional spacers can be added (5mm to 10mm) above the stem. Note that some of the larger computers will not always work with a steep angled stem. Designed with mountain biking in mind, the K-EDGE Stem mount is also ideal for much more including: cyclocross; triathlon; bike touring; or if you simply prefer this position for your computer.

Mounting for Shimano Di2

The K-EDGE Garmin Stem Mount is a great upgrade solution for cyclists who prefer their computer above the stem. Mounting off of the steerer tube, the mount replaces a standard 5mm spacer, and is locked securely in place by the top cap compression system. The fixed version is recommended for zero degree or negative degree stem angles. Can also be used with positive degree stems if additional spacers added (5mm to 10mm) above the stem. Designed with mountain biking in mind, the K-EDGE Stem mount is also ideal for much more including: cyclocross; triathlon; bike touring; or if you simply prefer this position for your computer. - Compatibly – 1-1/8" Steerer tube Diameter, Thickness (@ Steerer) – 5mm, Length (Center-to-Center) – 50mm, - Recommended for 0 Degree to Negative Degree Stem Angles - Supported Computers – Garmin Edge 20, 25, 200, 500, 510, 520, 800, 810, and Forerunner 310XT - CNC Machined 6061-T6 Aluminum Platform, Injection Molded Copolymer Interface - Made in Boise, Idaho, USA - Lifetime Guarantee against material or manufacture defects. Damages due to abuse or crashing excluded.

NEW K-EDGE Go Pro Style Top Cap is an ideal position for your camera or light. This mount replaces your top cap with a functional camera/light mount. Not all of these Top Cap mounts are created equal. The precision fit of the K-EDGE Mount is critical to both proper headset compression AND camera security. Whether dropping into a World Cup Downhill descent or simply following your kids on a family ride, enjoy the convenience of this GoPro style mount. - Clean, sleek, (replaces top cap) - Ideal position, centered, above cockpit - Ultimate Enduro, DH, filming platform - Adaptable camera or light mount - CNC Machined, one piece, lifetime warranty - All hardware included